# Sandblast stencil film: choosing rubber or PVC, and 0.5 to 1.1 mm

How monument and glass workshops choose between natural-rubber and PVC sandblast stencil, which gauge suits which job, and why Mylar backing matters.

Published 2026-08-11, updated 2026-09-30, by the Lizhou technical team.

## Key takeaways

- Natural-rubber stencil absorbs abrasive impact and suits deep carving in granite and stone; PVC stencil suits shallower work, glass and fine detail.
- Thicker gauges (1.0–1.1 mm) protect the surface longer under aggressive blasting; thinner films (0.5 mm and below) cut finer detail.
- A clear Mylar (PET) backing holds small islands of a cut design in register while you transfer the stencil.
- Match the stencil width to your plotter or cutting table: 0.305 m and 0.61 m are standard.

A sandblast stencil has one job: keep abrasive away from everything you do not want to cut. Get the material right and the stencil survives the full blast, edges stay crisp and lettering comes out clean. Get it wrong and the stencil burns through halfway, or the fine detail of a design lifts before you have finished.

Here is how stone and glass workshops choose.

## Natural rubber or PVC?

**Natural-rubber stencil** is resilient. It absorbs the impact of abrasive particles instead of being cut by them, which makes it the standard choice for deep carving in granite, marble and other hard stone — headstones, monuments and memorial plaques. Our rubber stencils come in single-line, double-line and three-layer constructions.

**PVC stencil** is firmer and more economical. It holds fine detail well and suits glass etching, shallower stone engraving and decorative work. We supply PVC stencil from 0.08 mm up to 0.75 mm, in green, pink, yellow, blue, brown and grey — useful when operators want to see the stencil clearly against a particular stone colour.

A simple rule: the deeper and longer the blast, the more you want rubber.

## Which thickness?

| Gauge | Typical use |
| --- | --- |
| 0.08–0.5 mm PVC | Glass etching, fine detail, shallow surface frosting |
| 0.5 mm PVC (soft) | General stone engraving, lettering, printable die-cut stencils |
| 0.9–1.0 mm rubber | Standard monument lettering and ornament in granite |
| 1.1 mm rubber | Deep carving, shaped carving, long blast times |

Thicker stencil protects for longer but is harder to cut finely and to weed. Thinner stencil cuts finer detail but wears through sooner. Most monument workshops keep two gauges in stock: one for lettering and one for deep ornamental work.

## Why Mylar backing matters

When you cut a stencil, some pieces float free — the centre of an "O", the inside of a leaf. A **clear Mylar (PET) backing** holds every piece in its exact position during transfer, so the design goes onto the stone in register. It is particularly useful for:

- Lettering with closed counters (A, B, D, O, P, R)
- Complex ornament and floral designs
- Photo-stencil and printed die-cut designs

Our three-layer rubber stencil and several PVC grades are available with Mylar backing.

## Width, length and cutting

Standard widths are **0.305 m** and **0.61 m**, on paper-core rolls. Lengths vary by grade, and we cut to length for production orders. PVC stencil is also available in 1.22 m widths for larger panels.

Before ordering, check the maximum material thickness of your plotter or stencil cutter. Thinner and printable grades suit many plotters; thick rubber is often cut by hand or on dedicated equipment.

## Good practice in the workshop

- **Clean the stone** thoroughly: dust and polishing residue weaken adhesion.
- **Apply firmly** with a squeegee, working from the centre out to avoid trapped air.
- **Store rolls** cool and dry, away from direct sunlight; rubber adhesives age faster in heat.
- **Test new gauges** on an offcut before using them on a finished memorial.

## Also in this range: PE protective film and masking

Our stencil line includes **self-adhesive PE surface-protection film** (blue or transparent, 0.03–0.2 mm) for protecting polished stone, glass and aluminium profiles during fabrication and transport, plus crepe-paper masking tape in jumbo rolls.

Browse the [sandblast stencil range](https://lizhou-newmaterial.com/products/sandblast-stencil-film/), or [ask for sample pieces](https://lizhou-newmaterial.com/contact/?type=samples&category=sandblast-stencil-film) in two gauges to test on your own stone.

## FAQ

**What thickness of sandblast stencil should I use for tombstones?**
For deep carving in granite and hard stone, most workshops use natural-rubber stencil in 1.0–1.1 mm. The thicker film resists the abrasive for longer, so you can blast deeper before the stencil wears through.

**Can sandblast stencil be cut on a vinyl plotter?**
Thinner PVC stencils and printable die-cut grades can be cut on suitable plotters. Thick rubber stencils are usually cut by hand or on machines designed for stencil material. Check your cutter's maximum material thickness before ordering.

**What is the Mylar backing on sandblast stencil for?**
A clear Mylar (PET) backing acts as a carrier that keeps all parts of a cut design in position during transfer, which matters for lettering with loose counters and for fine ornamental detail.

---
Guangdong Lizhou New Materials Technology Co., Ltd. — sales@lizhou-material.com — +86 137 2833 8858 (WhatsApp) — https://lizhou-newmaterial.com/contact/
